Видео

This was awesome 👏. Thank you❤

My Is doing the same, but my furnace is off, it's summer. What could it be??

Brilliant!!! I’m going to try this on my earth air tunnel to seal the barrel connections!!

Hit the Gym.

Very helpful. Thanks 🙏

In the summer use a small amount of ice in the top bucket or old water.

I use ice in the top bucket for a short time. Which causes that top bucket to shrink. Could also use cold water

Hi. My grape vine already has black rot. Will this stop the spread and save my vine and grapes on them. Thank you.

hey fellow Harbor frt enthusiast ! where did you get the blades ?

That is awesome great job!

I bought this from Vevor works really well cleaning my pond also bought one they had that can throw in the pond and pull out with mower or ATv to get the mess on the bottom. Worth every penny for what I am using it for. Also nice homestead and TY for sharing your review.

Thank you. M

Are you using a reg 15 amp cb or a kitchen 20 amp cb? Does it trip breakers? Can the blades be removed / replaced?

It seems like this video is old but it still works, thank you very much.

OH NO, you threw them away?

Since they are filled with crevices then fill them with high strength concrete

WONDER how these would do with a lower front end car like a Focus?

LOL , has this guy NEVER used ramps before, it's best to start a fot or more behind them & take a running start

They hold up better than expected. I've had them four 5 years worked with them several summers on an F150. In up to 105 Fahrenheit heat.

mine have brown little dots and yellow leaves

Do I need to cut the damaged leaves off first before spraying?

do they nest together for storage?

I inherited this stove from the person I bought my house from. All the screws inside the stove look really rusty. The 2 screws that hold the igniter in place were seized, I ended up breaking the head off both screws. I took the gas/flame tube out, I think I'm going to drill out the remaining piece of both igniter screws, and replace with a screw/nut combo from the hardware store.

lol this one board costs hundreds of dollars in time alone

Clean the pipe with sandpaper on each side of the valve first and then use a mini hacksaw to cut closer to the old valve.

don't try air up a truck tire mine starting melting after it got 20 lbs air in 10 mins

How loud is this pump?

I have about 60 ft of pipe and fittings to replace in my basement (heater radiator lines) I need to tackle 💯🤷🏻‍♂️🤦🏻‍♂️

I use the metal Jerry cans here in OZ, I think the 1st one would be better even though it wouldn't store as well in the vehical

Thanks for the tips.

This will attack the aluminum gutters.

Unplugging ethernet cable and cycling power on the wifi router worked on junk a*s netgear expensive a*s equipment. Thank you liked and subbed

That pit looks much older than what you said! Good job.

Damm it worker for me disconnect the wires and reset !! 3:09am san antonio tx

Awesome, thankyou, didnt know this. excellent❤

some of my potato leaves have tiny little yellow spots and holes on them. lots of them wish i could show you a picture---what could this be?

Great work buddy. How's it holding up?

Great video. What happens if you stop the water flow at the sprayer nozzle? Will the pump still function normally?

Flame thrower

Your better off using a pressure washer.

If you droll the bolt holes slightly off, wouldn't that mean you can't adjust the horizontal level on each side? The only way it would work is if you drilled the bolt holes oversized, that way you can adjust both sides when tightened down. Just my thoughts.

IMO the ugliest garden plant ever. I pulled mine out ages ago.

Do the pallet walls stay upright just by being secured to one another at the corners? Or are there posts in their interior spaces holding them in place?

Its bad no colour brown

THAAAAANKKKKK UUUUUUUU

Watchingyou smooth with the small scraper, I realized a ROLLING PIN might be easier and is washable. Js

I like it! Thank you.

Nextime have the wife in front..holding ramps from sliding..😂

Hair dryer and fingers: Make small crevice between buckets prying with fingers and thumbs of one hand and direct hot air of hair dryer down the gap. Keep maneuvering the gap around and eventually hot air pops them apart.

You can put about 2 cups of the crystals in a gallon of water and what doesn't dissolve means the water can't absorb any more copper; you now have a solution that can be added at 8 ounces per gallon of water to your sprayer. Leave whatever doesn't dissolve and add more crystals to make some more solution, you'll end up with more solution than you could use in a lifetime. Add a squirt of dish soap to act as a Surfactant so that it will stick to the roof and mold and not run off. You can also add the dish soap to some water and Bleach and spray it on to kill everything first and then spray on the Copper to keep it off the roof, the copper should stay on the roof for some time.